Mplab xc8 configuration bits
#pragma config WDTPS = 1, CCP2MX = DEFAULT #FUSES INTRC //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD)
![mplab xc8 configuration bits mplab xc8 configuration bits](http://codigoelectronica.com/public/attach/images/uploads/2019/05/base-mplab-xc8-configurar-bits.jpg)
![mplab xc8 configuration bits mplab xc8 configuration bits](https://singularengineer.com/wp-content/uploads/2013/04/newproject.png)
#FUSES NOFCMEN //Fail-safe clock monitor disabled #FUSES NOIESO //Internal External Switch Over mode disabled #pragma config IESO = OFF, FCMEN = OFF, FOSC2 = OFF, FOSC = HS #FUSES NOPROTECT //Code not protected from reading #FUSES STVREN //Stack full/underflow will cause reset #FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode) #FUSES DEBUG //Debug mode for use with ICD #pragma config DEBUG = ON, XINST = OFF, STVREN = ON, WDTEN = OFF My configuration bits are set as seen below: I am using the PIC18F65j90 and I want to select the INTOSC Internal Fast RC (8 MHz) oscillator mode. Please do not post bug Reports on this forum.
MPLAB XC8 CONFIGURATION BITS CODE
CONFIG1#pragma config FOSC = ECH // External Clock, 4-20 MHz#pragma config WDTE = OFF // Watchdog Timer (WDT) disabled#pragma config PWRTE = OFF // Power-up Timer disabled#pragma config MCLRE = ON // MCLR/VPP pin function is MCLR#pragma config CP = OFF // Flash Memory Code Protection off#pragma config BOREN = ON // Brown-out Reset enabled#pragma config CLKOUTEN = OFF // Clock Out disabled.CCS :: View topic - Configuration bits setupįAQ Forum Help Official CCS Support Search Register Profile Log in to check your private messages Log inĬCS does not monitor this forum on a regular basis. 6 2016-2017 Microchip Technology Inc.Ģ.1 while() D B LED ( / ) LEDS_ON_OFF LEDS_OFF_ON while(1) Ģ.2 _delay()LED _delay()MPLAB XC8 C Compiler Users Guide(DS50002053)Ģ016-2017 Microchip Technology Inc. LATD = LEDS_OFF_ON // RD = LED LATB = LEDS_OFF_ON // RB = LED _delay(INSTR_CYCLE_DELAY) // delay in instruction cyclesĭS50002400B_JP - p. _delay(INSTR_CYCLE_DELAY) // delay in instruction cycles LATD = LEDS_ON_OFF // RD = LED LATB = LEDS_ON_OFF // RB = LED Port B access ANSELB = 0x0 // set to digital I/O (not analog) TRISB = 0x0 // set all port bits to be output Port D access ANSELD = 0x0 // set to digital I/O (not analog) TRISD = 0x0 // set all port bits to be output #define LEDS_ON_OFF 0x05#define LEDS_OFF_ON 0x0A#define INSTR_CYCLE_DELAY 25000 PIC16F1719 Configuration Bit Settings// For more on Configuration Bits, consult your device data sheet TRISD = 0x0 // set all port bits to be outputĢ016-2017 Microchip Technology Inc. LATD = LEDS_ON_OFF // write to port latch - RD = LED ( ) TRIS TRISD TRISB01 D 4 2016-2017 Microchip Technology Inc.ġ.3 LED LED (LEDS_ON_OFF) : (LED D1D3D5D7 ONLED D2D4D6D8 OFF)Explorer 8 Development Board Users Guide(DS40001812) B.4Explorer 8ĪNSELD = 0x0 // set to digital I/O (not analog) I/O (PORT) (LAT) LATD LATBLEDS_ON_OFF D MPLAB XC8 Installation Directory/docs/chips Port B access ANSELB = 0x0 // set to digital I/O (not analog) TRISB = 0x0 // set all port bits to be output LATB = LEDS_ON_OFF // write to port latch - RB = LED return }Ģ016-2017 Microchip Technology Inc.
![mplab xc8 configuration bits mplab xc8 configuration bits](https://i.stack.imgur.com/gkv0F.png)
CONFIG2#pragma config WRT = OFF // Flash Memory Self-Write Protect off#pragma config PPS1WAY = ON // PPS one-way control enabled#pragma config ZCDDIS = ON // Zero-cross detect disabled#pragma config PLLEN = OFF // Phase Lock Loop disable#pragma config STVREN = ON // Stack Over/Underflow Reset enabled#pragma config BORV = LO // Brown-out Reset low trip point#pragma config LPBOR = OFF // Low-Power Brown Out Reset disabled#pragma config LVP = OFF // Low-Voltage Programming disabledĪNSELD = 0x0 // set to digital I/O (not analog) TRISD = 0x0 // set all port bits to be output LATD = LEDS_ON_OFF // write to port latch - RD = LED CONFIG1#pragma config FOSC = ECH // External Clock, 4-20 MHz#pragma config WDTE = OFF // Watchdog Timer (WDT) disabled#pragma config PWRTE = OFF // Power-up Timer disabled#pragma config MCLRE = ON // MCLR/VPP pin function is MCLR#pragma config CP = OFF // Flash Memory Code Protection off#pragma config BOREN = ON // Brown-out Reset enabled#pragma config CLKOUTEN = OFF // Clock Out disabled.#pragma config IESO = ON // Internal/External Switchover on#pragma config FCMEN = ON // Fail-Safe Clock Monitor enabled For more on Configuration Bits, // consult your device data sheet